Vibroplex bug manual. Original

BUGKEY ADJUSTMENT AND SENDING mobile.eyeslipsface.com

Vibroplex bug manual

For more information about the different Vibroplex models, including how to estimate the date your key was made from the serial number, check out. The Model 4 was also available on a standard 3. Several other manufacturers made clones and copies of Vibroplexes, some legal and some illegal. Bunnell then produced these keys under the name 'Bunnell Martin Flash keys. It is silky smooth to borrow that phrase from another product. Naming of Parts The parts of the Bencher need to be understood before an attempt is made to adjust the paddle. A free arm movement should be used.

Nächster

Comparing older Vibroplex bug to new

Vibroplex bug manual

The first version of the Autoplex, which is quite rare, was built on a wooden base. Pushing a paddle mounted on one end of the lever to the right and holding it there caused a spring-mounted contact on the other end of the lever to vibrate against a stationary contact, making strings of dots. Copyright © 1997-2013, Randy Cole. However another inventor named William Coffe filed a patent on 11 January 1904. Start with slow speed adjustment.

Nächster

More Vibroplex Bug Practice tips

Vibroplex bug manual

This screw adjusts the width of the pendulum's arc, and to the extent that the pendulum moves farther than is necessary for an instantaneous meeting of the dot contacts, the contacts stay closed or dwell until the pendulum swings back. Vibroplex 'Lightning Bug' After the First World War, it took a few years before the next major introduction occurred. If the electronics in the keyer cannot determine which contact hit first logically simultaneous , it will default to starting with either a dit or a dah and then begin alternating. The solid base does not move at all while sending. Pressing the handle to the left sends a dash of any required length, hence the signal may be emphasized by lengthening or shortening dashes independently of the speed of the dots, which is a very important feature either in Morse or Continental transmission.

Nächster

Vibroplex Vibrokeyer Morse Key

Vibroplex bug manual

Now back the screw off until just the point at which the arm moves freely again- usually it's just a fraction of a degree of screw rotation, or about as fine an adjustment as you can make. It's a bit of an intimidating instrument, both in appearance and in operation. There is no reason the tension should be the same if you don't want it that way. Bearing Tension, adjustable only as a side-effect of varying the spring tension on the pivot plate. Critical parts or adjustment screws are indicated in the The two paddle arms are the S shaped pieces of metal which have the plastic finger-piece at the front and a contact at the other end, adjacent to the two contact post s.

Nächster

More Vibroplex Bug Practice tips

Vibroplex bug manual

Loosen the transverse locking screw the smaller, upper one on each contact post and then back out the contact screw until the contact itself is up against the inner surface of the post. In addition, the Lionel Corporation yes, the model train company also made J-36 keys of the same design for the Army. And, you get the same crisp operation at 5 words per minute as you do at 50+ wpm. Adjust the resting position of the pendulum. In 1923, the Lightning Bug incorporated several improvements and enabled smooth and efficient Morse transmission. Due to its small size and light weight, the key required the use of a fold out extension leg to help keep it stable on the operating table.

Nächster

Identify

Vibroplex bug manual

The frame was no longer cast, but was assembled from two triangular plates and two vertical cylinders. Typewriter 'keys' Another solution that was investigated was that of using a form of typewriter that generated Morse characters when the keys were depressed. You won't find exactly the same parts on every instrument, but usually you can figure out what does what if you understand the basics. The mainspring was fastened in a slot in the lever arm, and after loosening two small screws, the user could move the mainspring in or out, effectively shortening or lengthening the mainspring and changing its rate of vibration. An example can be seen above, at the right. Bearing Tension, the setting of the pivot bearings on which the arm rotates.

Nächster

Vibroplex Operation Manual

Vibroplex bug manual

Loosen the bearing tension screw A until the arms wobble loosely. With needle bearings and nylon seats, it is essentially ignorable. The earlier Norcross keys were built using a metal base that was much thinner than the orginal design which required the use of a fold-out extension leg to keep the key from moving around on the table. Contact Spacing, the space between the two electrical contacts when the key arm is not depressed unkeyed. If the arms have separate bearing adjustments, perform this adjustment for each arm individually. Check and adjust the pivot bearing tension.

Nächster

Vibroplex History: Mechanical Bug Key » Electronics Notes

Vibroplex bug manual

The spring attaches to a long screw that goes through the pivot plate from the upper quadrant. Now back the screw off until just the point at which the arms move freely again- usually it's just a fraction of a degree of screw rotation, or about as fine an adjustment as you can make. The contacts on the Bencher are an adjustable contact on the end of a screw going through the contact post, and a fixed contact on the end of the paddle arm. The series can start with either a dit or a dah, depending on which lever makes contact first. The lever arm pivots in the famous chromed mainframe.

Nächster